If you have been reading about low-binding tubes and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2026-02-06. Where a claim depends on a specific study, the study is described rather than over-claimed.
Reconstitution solvent depends on peptide solubility and intended use; water, buffer, or small amounts of organic solvent may be needed. After dissolution, solutions are typically aliquoted into single-use portions to avoid repeated freeze-thaw cycles. Aliquots are stored at -20 °C or -80 °C, depending on stability. Labels include concentration, solvent, date, and operator. Sterile filtration may be used when microbial control is required, but filters can adsorb peptides. The optimal concentration and solvent are often determined empirically.
Cold-chain shipping uses insulated containers, phase-change packs, and temperature indicators. Dry ice maintains -70 °C or lower but requires venting to avoid pressure buildup. Gel packs provide 2-8 °C for shorter transit. Upon arrival, recipients should record temperature indicators and transfer vials promptly to storage. Deviations from specified conditions should be documented and may require analytical re-check. The effect of a brief temperature excursion is peptide-specific and not always predictable from general rules.
Handling begins with receipt and inspection. Vials should be checked for damage, label integrity, and temperature history. Lyophilized peptides should be allowed to equilibrate to room temperature before opening to prevent condensation. Solutions should be prepared in a clean, calibrated environment using appropriate solvents. Personal protective equipment and containment reduce exposure and contamination. Documentation of lot number, date, and storage location supports traceability. The goal is to limit repeated temperature changes, moisture exposure, and microbial contamination.
Light exposure can damage aromatic residues and certain labels, so amber vials or opaque containers are often used. pH control matters in solution, as extreme acidity or alkalinity accelerates backbone cleavage; buffers may also introduce ions that affect solubility. Microbial growth is a concern for aqueous preparations that lack preservatives, though many research peptides are handled in sterile or low-bioburden conditions. Container materials can adsorb peptides, particularly hydrophobic or positively charged sequences, reducing recovery. These factors interact, meaning storage decisions balance chemical stability, physical state, and intended use.
Peptides are short chains of amino acids whose physical and chemical stability depends on sequence, length, and conformation. The amide backbone can hydrolyze under acidic or basic conditions, while side chains such as methionine, cysteine, and tryptophan are prone to oxidation. Aggregation may occur when hydrophobic regions associate, especially near surfaces or at high concentration. Because these pathways differ among peptides, no single storage condition applies to all sequences. Stability studies therefore examine each peptide under defined temperature, pH, and humidity ranges.
| Property | Value | Notes |
|---|---|---|
| Form | Lyophilized powder or frozen solution | Powder is generally more stable for long-term storage. |
| Recommended storage | -20 °C, desiccated, protected from light | -80 °C for solutions or sensitive sequences. |
| Reconstitution solvent | Water, buffer, or organic co-solvent | Choice depends on peptide solubility and assay. |
| Freeze-thaw stability | Limited; avoid repeated cycles | Aliquoting into single-use portions reduces damage. |
| Contamination control | Aseptic technique and sterile filtration | Filters may adsorb peptides; validate recovery. |
After reconstitution, solutions are divided into single-use aliquots and stored at -80°C. Labels include peptide name, concentration, buffer composition, date, and lot number. Freeze-thaw cycles are minimized by thawing only the needed aliquot on ice or at room temperature. Some peptides benefit from the addition of a carrier protein, such as bovine serum albumin, or a cryoprotectant like glycerol to reduce adsorption to plastic. Glass vials with low-binding surfaces are preferred for dilute solutions. Shipping of frozen aliquots uses dry ice and insulated containers to maintain the cold chain.
Receiving a peptide shipment requires immediate inspection of the packaging and temperature indicators. Any deviation from the specified cold chain should be documented and investigated. Upon arrival, solid peptides are generally kept at -20°C, whereas liquid formulations are stored at -80°C. Vials should be kept upright and protected from light. Repeated warming and cooling of the entire container is avoided by preparing smaller working aliquots. A log of lot numbers, receipt dates, and storage locations supports traceability and quality control.
After reconstitution, dividing the solution into single-use aliquots limits multiple warming and cooling events and reduces contamination risk. Low-binding polypropylene tubes are often preferred because peptides can adsorb to glass or untreated plastic surfaces. Filling headspace with nitrogen or argon can slow oxidation, and amber or foil-wrapped containers reduce photodegradation. Each aliquot should be labeled with peptide identity, concentration, date, and storage conditions. Frozen aliquots should be thawed quickly and kept on ice until use.
When a peptide arrives, the vial should be inspected for damage, and its label, lot number, and accompanying analytical data should be recorded. Cold vials should equilibrate to room temperature before opening to prevent condensation on the powder. Moisture uptake can reduce stability and complicate accurate weighing or reconstitution. Inventory systems that track date, quantity, and storage location help prevent unnecessary temperature cycling. Personnel should follow institutional or manufacturer instructions for any specific peptide.
Reconstitution is often performed with sterile water, buffer, or a water-miscible organic solvent, depending on solubility. The solvent should be added gently along the vial wall, and the solution mixed by gentle swirling rather than vigorous vortexing, which can cause foaming and surface denaturation. Some sequences require a small amount of base or acid to dissolve, followed by pH adjustment. Preparing a concentrated stock solution can simplify later dilution, but the stock itself may have limited stability. Records of solvent, concentration, and date support reproducibility.
Cold-chain practice relies on documented temperature ranges, calibrated monitoring, and minimized excursions. Shipments may use insulated boxes, phase-change materials, or dry ice, with data loggers to record conditions. Upon receipt, the recipient should verify the logger trace and place items into long-term storage promptly. Repeated warming and cooling during transfers can be more harmful than a single controlled excursion. For solutions, dividing material into single-use aliquots reduces the number of thawing and refreezing events and limits repeated opening of the same container.
Handling begins before a peptide arrives at the bench. Containers should be inspected for cracks, loose caps, or visible moisture, and labels should record identity, lot, and receipt date. Lyophilized material is often allowed to equilibrate to room temperature before opening to prevent condensation on the powder. Gloves and a clean workspace reduce contamination and static-related loss. Once opened, the vial may be purged with inert gas and resealed if the peptide is sensitive to oxygen or humidity. These steps are procedural safeguards rather than guarantees of stability.
Reconstitution introduces new risks because the peptide contacts solvent, air, and container surfaces. The chosen solvent should match the peptide's solubility profile, and buffer salts, pH, and ionic strength can affect dissolution and subsequent stability. Gentle mixing is preferred over vigorous vortexing, which can create interfaces and shear. If the solution is not clear, the cause may be incomplete dissolution, aggregation, or insoluble counter-ions rather than a simple concentration problem. Filtration is sometimes used, but filters can adsorb peptides and alter measured concentration.
Shipping and short-term transfer require attention to temperature control and physical stability. Frozen solutions are commonly sent on dry ice, while lyophilized powders may travel with gel packs or insulated packaging. Thawing should be done slowly on ice or in a refrigerator, not by vigorous heating, and the solution should be mixed gently before use. Temperature loggers can document excursions during transit, but their presence does not prove that a peptide remained stable. Analytical checks such as chromatography or mass spectrometry can verify identity and purity after storage or shipping.
Reconstitution begins with selecting a solvent that dissolves the peptide without causing degradation. Water or aqueous buffer is suitable for many hydrophilic sequences, while hydrophobic peptides may require a small amount of organic solvent such as acetonitrile or dimethyl sulfoxide before dilution. The solvent is added to the vial rather than the powder being scraped out, and the mixture is swirled or inverted gently to avoid foaming. Complete dissolution should be confirmed visually, and insoluble material may indicate aggregation or impurities. Because solvent tolerance varies, published solubility information or a small test dissolution can guide handling.
Aseptic technique reduces microbial and particulate contamination when a peptide solution will be used in cell culture or other sensitive applications. Work in a clean area, use sterile containers and filtered tips, and avoid touching vial interiors. Preparing aliquots immediately after dissolution limits repeated temperature cycling, which is a common cause of aggregation and activity loss. Low-binding plastic tubes are preferred for peptides that adsorb to surfaces, especially hydrophobic or positively charged sequences. Labels should record identity, solvent, concentration, and preparation date so that later use can be traced.
In 1979, IUPAC suggested systematic element names to be used as placeholders until permanent names were established; under it, element 105 would be unnilpentium, from the Latin roots un- and nil- and the Greek root pent- (meaning "one", "zero", and "five", respectively, the digits of the atomic number). Both teams ignored it as they did not wish to weaken their outstanding claims. In 1981, the Gesellschaft für Schwerionenforschung (GSI; Society for Heavy Ion Research) in Darmstadt, Hesse, West Germany, claimed synthesis of element 107; their report came out five years after the first report from JINR but with greater precision, making a more solid claim on discovery. GSI acknowledged JINR's efforts by suggesting the name nielsbohrium for the new element. JINR did not suggest a new name for element 105, stating it was more important to determine its discoverers first.
== Function == Κ-casein is involved in several important physiological processes in milk. Chymosin (found in rennet) cleaves κ-casein into an insoluble peptide, para-κ-casein, and a water-soluble glycomacropeptide (GMP). Milk-clotting proteases act on the soluble portion of κ-casein, generating an unstable micellar state that results in clot formation.
Analytes that are totally excluded, elute with the free volume outside around the particles (Vo), the total exclusion limit, while analytes that are completely delayed, elute with the solvent, marking the total permeation volume of the column, including also the solvent held inside the pores (Vi). The total volume can be considered by the following equation, where Vg is the volume of the polymer gel and Vt is the total volume:
== Medical uses == EMP is indicated, in the United States, for the palliative treatment of metastatic and/or progressive prostate cancer, whereas in the United Kingdom it is indicated for the treatment of unresponsive or relapsing prostate cancer. The medication is usually reserved for use in hormone-refractory cases of prostate cancer, although it has been used as a first-line monotherapy as well. Response rates with EMP in prostate cancer are said to be equivalent to conventional high-dose estrogen therapy. Due to its relatively severe side effects and toxicity, EMP has rarely been used in the treatment of prostate cancer. This is especially true in Western countries today. As a result, and also due to the scarce side effects of gonadotropin-releasing hormone modulators (GnRH modulators) like leuprorelin, EMP was almost abandoned. However, encouraging clinical research findings resulted in renewed interest of EMP for the treatment of prostate cancer. EMP has been used at doses of 140 to 1,400 mg/day orally in the treatment of prostate cancer. However, oral EMP is most commonly used at a dose of 560 to 640 mg/day (280–320 mg twice daily). The recommended dosage of oral EMP in the Food and Drug Administration (FDA) label for Emcyt is 14 mg per kg of body weight (i.e., one 140 mg oral capsule for each 10 kg or 22 lbs of body weight) given in 3 or 4 divided doses per day. The label states that most patients in studies of oral EMP in the United States have received 10 to 16 mg per kg per day. This would be about 900 to 1,440 mg/day for a 90-kg or 200-lb man.
Amine groups are found throughout an antibody and are used as a target due to their easy steric accessibility and modification. An overview of this reaction is found in Figure 2. Most often amine groups found on lysine are covalently bonded to carboxyl groups of glutamic and aspartic acid on formed liposomes using certain agents. A two step process is utilized where the first step uses 1-ethyl-3-[3-dimethylaminopropyl] carbodiimide to create an amine reactive product from the carboxyl group. This product is a target for a nucleophilic attack by the amine but it hydrolyzes quickly, so EDC is added to stabilize it. As seen in the Figure 2, the intermediate can lead to the desired stable amide bond by chance or the recreation of a carboxyl group. To create more of the desired carboxyl-amine bond, N-hydroxysulfosuccinimide (sulfo-NHS) is added to form another intermediate that is an NHS ester. The second step to this reaction is for the antibodies to use the N-terminus of the lipid to covalently conjugate by creating an amide bond via displacement of sulfo-NHS groups. This leads to the final product of an antibody conjugated to a liposome to create an immunoliposome. This process is highly efficient and effective while maintaining the biological activity of the antibody.
Sources: en.wikipedia.org
== Reaction == Penning ionization refers to the interaction between an electronically excited gas-phase atom G* and a target molecule M. The collision results in the ionization of the molecule yielding a cation M+●, an electron e−, and a neutral gas molecule, G, in the ground state. Penning ionization occurs via formation of a high energy collision complex, evolving toward the formation of a cationic species, by ejecting a high energy electron.
=== Popular culture === In the 2001 comedy film Evolution selenium was mentioned as an active ingredient of the anti-dandruff shampoo Head & Shoulders. A group of academics, therefore, tried to use this brand of shampoo to stop an alien invasion after discovering that the alien life form was sensitive to selenium.
=== Service industry === In 2017, the total output (gross value added) in the service industry amounted to 75.2% of total output in Denmark, and 79.9% of all employed people worked in this industry in 2016. Apart from public administration, education and health services, main service sub-industries were trade and transport services, and business services.
The article contains both the theory in terms of the partition coefficient of a compound, and application to the separation of amino acids on a water-impregnated silica column eluted with a water:chloroform:n-butanol mixture.
== Biosynthesis == NAAG synthetase activity mediates the biosynthesis of NAAG from glutamate and NAA, but little is known about the mechanism or regulation of this enzyme, and no NAAG synthetase activity has been isolated in cell-free preparations. Since other neuropeptides and nearly all vertebrate peptides are synthesized by post-translational processing, NAAG synthetase activity is relatively unique. As with NAA, the synthesis of NAAG is primarily restricted to neurons, although glial cells also contain and synthesize this peptide. In vitro, NAAG synthesis appears to be regulated by the availability of its precursor, NAA. In addition, during differentiation of neuroblastoma cells, it has been shown that a protein kinase A (PKA) activator will increase the quantity of NAAG, while a protein kinase C (PKC) activator will decrease its concentration. This finding suggests that PKA and PKC have opposing regulatory effects on the NAAG synthetase enzyme.
Sources: en.wikipedia.org
No. Allowing the sealed vial to equilibrate to room temperature reduces condensation on the powder. Condensation can introduce moisture and promote degradation. Equilibration usually takes 15 to 30 minutes depending on vial size.
Aliquoting limits repeated freeze-thaw cycles that can cause aggregation or loss. Single-use portions reduce contamination risk and handling variability. It also allows separate testing without disturbing the main stock.
Inspect packaging, temperature indicators, and vial condition before storage. Record any deviations from the expected temperature range. If a deviation occurred, analytical testing may be warranted before use.
Freezing slows hydrolysis and oxidation by reducing molecular motion and available water. Lyophilized powders contain little moisture, so they can remain stable for extended periods when kept cold and dry. The exact temperature depends on peptide sequence and expected storage duration.